America
!

Electric Horn Hardware Kit
!
Larger picture
EH290
Hardware kit used to install our electric horns onto Triumph America and Speedmaster. Mounts at lower rear of engine—hidden. Kits include a relay, fuse, all wiring, and mounting hardware along with detailed instructions.

Magnum Electric Horn Set
!
Larger picture
ELCHRN
While not as loud as our premium quality air horns, with an output of 118 decibels these are the loudest electric horns you can buy, over three times as loud as most stock horns and a great economical choice. A direct replacement for most 12-volt electric horns. The set includes two chrome finish horns (one high and one low tone), mounting brackets and installation instructions. We have several wiring and mounting kits available, call for model specific applications.

Note: While not included, we recommend the use of a relay part No. RELAY to achieve maximum volume and protect stock electrical system.

Passenger Boards
!
Larger picture
TA005
These boards are the ultimate in passenger comfort. They greatly increase foot and leg support, as well as allow a variation in foot position on long rides. Machined from billet aluminum, hand polished to a flawless finish, and triple chrome-plated. The inlaid rubber pads are made of soft anti-vibration neoprene to further ensure passenger comfort. They will fold and lock in the up position with spring-loaded detents.

Driving Lightbar - Triumph America
!
Larger picture
TA006
Gives your America a classic look as well more than doubling your forward and side illumination of the highway. This triple chrome-plated, billet aluminum design - includes 4.5" 34-watt driving lights, turn signal relocation adaptors, on-off switch, and all wiring. The set is compatible with all windshields. All the wires are concealed in the lightbar, lights are spaced at 22" center-to-center.

Solo Rack
!
Larger picture
TA010
Give your America the custom solo look that says, "No passengers, this ride is all about me". Laser cut, hand polished to a flawless finish and triple chrome-plated. Mounts using the same two bolt holes as the stock passenger seat so you can switch back to the seat in minutes (when it's all about taking someone along for the ride).

Triumph America/Speedmaster Sidestand Pad
!
Larger picture
TA013
This clever pad slides over the stock sidestand foot and is secured with a setscrew. It has over two time the area of the original. No more worries about your motorcycle falling over or fumbling around looking for your sidestand plate. Machined from billet aluminum and triple chrome-plated.

Triumph America Handlebar Risers
!
Larger picture
TA017
This set of handlebar risers are CNC machined from billet aluminum. Two versions available, either polished to a flawless finish and triple chrome-plated or finished in gloss black powder coat. They replace the stock risers and bring the handlebars back toward the rider 2". This significantly reduces the rider's back strain. Allows for a more relaxed "cruiser" syle of riding. Easy to install, retains all stock cables, hoses and wiring. This set also includes matching clamps.

Triumph America Driver Boards
!
Larger picture
TA024
Give your bike a highly customized look - especially when used with our matching passenger boards and highway pegs. Bolting on in place of the stock pegs they measure 8" x 5", provide full support for your feet, and are tipped back towards the rider at a 15 degree angle for maximum comfort. Machined from billet aluminum, hand-polished to a flawless finish and triple chrome-plated. Inlaid with soft anti-vibration neoprene rubber. The boards are hinged on their mounts and will fold up in the event of a tip over. Retains the stock shift and brake pedals while maintaining adequate foot room above and below.

Triumph America Front Caliper Cover
!
Larger picture
TA030

This front billet chrome-plated caliper cover hides most of the unsightly black and adds an eye-catching accent to the brake caliper. It attaches easily and securely with 3M VHB double-faced tape - "the good stuff".

Triumph America Front Turn Signal Relocators
!
Larger picture
TA104
This kit consists of two split clamps that attach to the fork tubes. The original signals mount directly to the split clamps. This greatly cleans up and improves the look of the bike by tucking the signals in close to the forks and eliminating the cheap black handlebar signal mounts.

Triumph America License/Turn Signal Relocator
!
Larger picture
TA105
One of the easiest things you can do to customize and clean up the appearance of your license plate, turn signals and tail light. Replaces the stock license/turn signal mounting bracket, installs easily without any drilling, wire cutting etc. It lays the license plate down against the fender and brings the turn signals in 4". It is laser cut from heavy gauge steel and triple chrome-plated. Also included is a set of our S.O.M.A. super bright, wide angle LED tail and brake lights. The seond most common motorcycle accident you are ever likely to face is being rear-ended and cruiser bikes are known for having small tail lights. While these LEDs are very small in size they give a huge increase in visibility to and safely from other motorists. For maximum visibility combine them with our flashing LED Brake Modulator linked below the pictures.

Optional Relocation Arms
!
Larger picture
TA005-5
Used to move the passenger boards forward 4" and have three different height adjustments. They will further increase passenger leg room and comfort. When saddlebags are installed on this model there is little or no room between the passenger peg and the saddlebag for the passenger’s heel. By moving the boards forward 4" you will gain the needed heel room as well as allow the passenger to be in a much more relaxed and comfortable seating position.