Road Star
!

Air Horns - Multi-Application
!
Larger picture
AHMULTI
Multiple Application Horn kit. Several mounting abilities and locations to fit most bikes, namely Yamaha V-Stars, Road Stars, and any other bikes with frame mounting ability or engine guards. These horns give a loud warning blast of 128 decibels all chrome finish.

The air compressor creates instant air pressure to the horns. Since the pressure is created so fast there is no need for a storage tank as on Semi Trucks and RVs. Although the pressure is very low (12-15 psi) it delivers a large volume of air (3 CFM or cubic feet per minute). This low-pressure high volume air supply causes the diaphragm inside the horn to vibrate at a high rate of speed or *frequency* the exact speed at which it vibrates is varied by the length of the horn or trumpet. Together the horn set produces an extremely loud 128-decibel warning blast. This is approximately 4 times louder than most electric motorcycle horns, which usually rate at 87 decibels.

Electric Horn Hardware Kit
!
Larger picture
EH300
Hardware kit used to install our electric horns onto Yamaha Road Star. Mounts in stock horns location. Kits include a relay, fuse, all wiring, and mounting hardware along with detailed instructions.

Magnum Electric Horn Set
!
Larger picture
ELCHRN
While not as loud as our premium quality air horns, with an output of 118 decibels these are the loudest electric horns you can buy, over three times as loud as most stock horns and a great economical choice. A direct replacement for most 12-volt electric horns. The set includes two chrome finish horns (one high and one low tone), mounting brackets and installation instructions. We have several wiring and mounting kits available, call for model specific applications.

Note: While not included, we recommend the use of a relay part No. RELAY to achieve maximum volume and protect stock electrical system.

Yamaha Road Star Passenger Boards
!
Larger picture
XV17005
These boards are the ultimate in passenger comfort! They greatly increase foot and leg support over stock pegs. These premium boards are CNC machined from billet aluminum and triple chrome-plated. The inlaid rubber pads are made of soft anti-vibration neoprene rubber to further insure passenger comfort. They are 2" further forward and 2" lower than the stock peg location for added passenger leg room. They will fold and lock in the up position with spring-loaded detents. Easy to install, fits all Road Star models. Shown with XV17005-5 Relocation Arms to move them another 4" forward and allow five different height positions.

Yamaha Road Star Passenger Board Relocation Arms
!
Larger picture
XV17005-5
Used to move the passenger boards forward 4" and allow for five different height adjustments. They will further increase passenger leg room and comfort. When saddlebags are installed on this model there is little or no room between the passenger peg and the saddlebag for the passengers heel. By moving the boards forward you will gain the needed heel room, as well as allow the passenger to be in a much more relaxed and comfortable seating position.

Yamaha Road Star Solo Rack
!
Larger picture
xv17010
Give your Road Star the custom solo look that says, "No passengers, this ride is all about me". Laser cut, hand polished to a flawless finish and triple chrome-plated. Mounts using the same two bolt holes as the stock passenger seat so you can switch back to the seat in minutes (when it's all about taking someone along for the ride).

Yamaha XV Handle Bar Risers

!
Larger picture
XV17017
This set of handlebar risers are CNC machined from billet aluminum, hand polished to a flawless finish, and triple chrome-plated. They replace the stock risers and bring the handlebars back toward the rider 2 1/4". This significantly reduces the rider's back strain. Allows for a more relaxed "cruiser" style of riding. Easy to install, retains all stock cables, hoses and wiring.

Yamaha Road Star License/Turn Signal Relocator
!
Larger picture
XV17105
Customize your look and increase safety! One of the easiest things you can do to customize and clean up the appearance of your license plate, turn signals and tail light. Replaces the stock license/turn signal mounting bracket, installs easily without any drilling, wire cutting etc. It lays the license plate down against the fender and brings the turn signals in 4". Laser cut from heavy gauge steel and triple chrome-plated.

Also included is a set of our S.O.M.A. super bright, wide-angle LED tail and brake lights. The second most common motorcycle accident your are ever likely to face is being rear-ended and cruiser bikes are known for having small tail lights. While these LEDs are very small in size, they give a huge increase in your visibility and safety from other motorists. For maximum visibility combine them with our flashing LED Brake Modulator (FLSH) linked below pictures.

PASS F/BOARDS ROADSTAR
!
BLV63750

PASS SW F/BOARDS XVS1600
!
BLV64750

SWEPT F/BOARDS XVS1600
!
BLV64250