GL 1500 Goldwing
!

Air Horns - Front Mount GL1500, 98 & Newer
!
Larger picture
AH98
These air horns give a loud warning blast of 128 decibels! Uses the stock horn button. Can be easily installed in 20-30 minutes.

All air horn sets are bolt on and plug-in, requiring about 30 minutes to install. They include the compressor, dust/bug covers, all necessary hardware, hoses, wiring, fuse, relay and detailed instructions with pictures.

The trumpets are triple plated chrome as well as the mounts and brackets so the shine and finish will last for years to come. They are completely waterproof. No hole drilling is required: bolt-on, plug-in installation. Cone shaped covers are included which mount to the front of the trumpets. One year unlimited warranty.

All kits include horn assembly, air compressor, relay, simple wiring and complete installation instructions. These horns mount to the front right side engine guard, with the compressor mounting to the frame behind the lowers.

The air compressor creates instant air pressure to the horns. Since the pressure is created so fast there is no need for a storage tank as on Semi Trucks and RVs. Although the pressure is very low (12-15 psi) it delivers a large volume of air (3 CFM or cubic feet per minute). This low-pressure high volume air supply causes the diaphragm inside the horn to vibrate at a high rate of speed or *frequency* the exact speed at which it vibrates is varied by the length of the horn or trumpet. Together the horn set produces an extremely loud 128-decibel warning blast. This is approximately 4 times louder than most electric motorcycle horns, which usually rate at 87 decibels.

A stock motorcycle horn draws only a small amount of power - less than 1 amp - which comes directly from the horn button on the handlebars producing the familiar weak motorcycle beep. The air horn's electric air compressor draws considerably more power - approximately 8 amps. This requires the use of a relay, heavier gauge wire and a fuse to prevent damage to the horn button contacts, as well as provide enough amperage to run the compressor at full speed. These components are included in the kit.

Air Horns - Front Mount

!
Larger picture
AHFRT
Front Mount Air Horns. Triple chrome plated. All Air horn systems are bolt on plug in applications. Requiring about 30 minutes to install. They include the horn set, dust/bug covers, all necessary hardware, hoses, wiring, fuse, relay, and detailed instructions with pictures.

The air compressor creates instant air pressure to the horns. Since the pressure is created so fast there is no need for a storage tank as on Semi Trucks and RVs. Although the pressure is very low (12-15 psi) it delivers a large volume of air (3 CFM or cubic feet per minute). This low-pressure high volume air supply causes the diaphragm inside the horn to vibrate at a high rate of speed or *frequency* the exact speed at which it vibrates is varied by the length of the horn or trumpet. Together the horn set produces an extremely loud 128-decibel warning blast. This is approximately 4 times louder than most electric motorcycle horns, which usually rate at 87 decibels.

Air Horns - Saddlebag Mount GL1500
!
Larger picture
AHSB
These air horns give a loud warning blast of 128 decibels! Uses the stock horn button. Can be easily installed in 20-30 minutes. The trumpets are triple plated chrome as well as the mounts and brackets so the finish and shine will last for years to come. They are completely waterproof. No hole drilling is required bolt-on, plug-in installation. Cone shaped covers are included which mount to the front of the trumpets. One year unlimited warranty. All kits include two horns, air compressor, relay, simple wiring and complete installation instructions.


The air compressor creates instant air pressure to the horns. Since the pressure is created so fast there is no need for a storage tank as on Semi Trucks and RVs. Although the pressure is very low (12-15 psi) it delivers a large volume of air (3 CFM or cubic feet per minute). This low-pressure high volume air supply causes the diaphragm inside the horn to vibrate at a high rate of speed or *frequency* the exact speed at which it vibrates is varied by the length of the horn or trumpet. Together the horn set produces an extremely loud 128-decibel warning blast. This is approximately 4 times louder than most electric motorcycle horns, which usually rate at 87 decibels.

GL 1500 Billet Aluminum Luggage Rack
!
Larger picture
AMA2010
This unique streamlined designed rack is CNC machine from solid billet aluminum. Has 3 neoprene pads for rack protection. Is hand-polished to a flawless finish and triple chrome-plated. Includes 1 1/4" billet mounting washers to better distribute the load.

Luggage Rack Base Washer Kit for GL1500
!
Larger picture
AMA2013
Fits other after market luggage racks. 1.25" diameter chromed with neoprene cushion and stainless back washer.

Electric Horn Hardware Kit - Honda GL1500
!
Larger picture
EH210
Hardware kit used to install our electric horns onto GL1500's. Mounts behind engine below the swing arm—hidden. Includes relay, fuse, all wiring and mounting hardware along with detailed instructions.

Magnum Electric Horn Set
!
Larger picture
ELCHRN
While not as loud as our premium quality air horns, with an output of 118 decibels these are the loudest electric horns you can buy, over three times as loud as most stock horns and a great economical choice. A direct replacement for most 12-volt electric horns. The set includes two chrome finish horns (one high and one low tone), mounting brackets and installation instructions. We have several wiring and mounting kits available, call for model specific applications.

Note: While not included, we recommend the use of a relay part No. RELAY to achieve maximum volume and protect stock electrical system.

Sidestand Pad - Honda GL1500
!
Larger picture
GL15013
No more worries about your motorcycle falling over or looking for a kick plate. Slips over stock sidestand and is secured with a set screw. Machined from billet aluminum with a black anodized coating. Has over twice the surface area of the stock sidestand.

Trunk Lid Organizer - Honda GL1500

!
Larger picture
GL15060
Pack your belongings away neatly and securely with this trunk lid organizer. Attaches easily to the inside of the trunk lid with existing screws. Mesh pockets for easy viewing secured with Velcro.

Also see the mathching rear trunk organizer #GL15062 and the saddlebag lid organizers #GL15061, sold seperately.

Saddlebag Lid Organizers – Honda GL1500
!
Larger picture
GL15061
Organize your saddlebags with these organizers. They attach to the inside of the saddlebag lid quickly. Mesh pockets for easy viewing of contents and are secured with velcro.

Inner Back Trunk Organizer - Honda GL1500
!
Larger picture
GL15062
Pack you belongings away neatly and securely with this rear trunk organizer. Attaches to the inner rear trunk wall, has mesh pockets for easy viewing of contents that close securely with Velcro.

Carpet Set for GL1500 Series
!
Larger picture
GL15063
Set of three deluxe carpets to line saddlebags and trunk

Parade Flag Holder (For Use W/Trailer Hitch)
!
Larger picture
PF900
This parade flag holder bar is designed to fit any motorcycle with a trailer hitch. It includes a chrome receiver bracket that is permanently bolted onto the trailer ball and will not interfere with your trailers coupler. The flag holder bar can then be installed or removed from the receiver bracket in seconds by removing two safety pins.

Included is one flag holder socket. One or two more can be added (sold separately) to accommodate up to three flags. The sockets accommodate up to 1 1/4” poles, and are machined at a 150 angle to their bases. They can be rotated and tightened to display your flags, angled to the rear, sides, diagonally, or any combination of these. All components are machined from aircraft quality aluminum and steel, then polished to a flawless finish and triple chrome-plated.

Parade Flag Holder Socket – Add-on

!
Larger picture
PF920
Order additional flag holder sockets to display two and/or three flags on holders PF900 and PF910, or up to four and five flags when used with optional PF930 add-on flag holder bar. Pricing is for one flag holder socket.

Parade Flag Holder - Add-on 4-5 Flag Holder Bar
!
Larger picture
PF930
Three flags not enough? This large flag holder bar accommodates one to five flags. It will replace the smaller bar on either model PF900 or PF910. Additional flag holder sockets are sold separately. (Must be used with PF900 Or PF910)

SuperBrace - Honda Goldwing 1500 - 1988-2000
!
Larger picture
SB2315

SuperBrace® is the leading motorcycle fork stabilizer. This patented brace provides better stability, superior aerodynamics and a more streamlined look than other multi-piece braces on the market.

  • Reduces low and high speed wobbles

  • Improves stability in tight cornering

  • Improves tire life and reduces cupping

  • Decreases sensitivity to rough road surfaces and rain grooves

  • Each SuperBrace is designed and manufactured for each specific motorcycle.

  • Every SuperBrace is made of 6061-T6 aircraft aluminum and machined to a tolerance of +/- .002 of oan inch, with a polished finish

  • Ten minute easy installation

  • Competition proven by world class racers

SWEPT F/BOARDS GL1500/C
!
BLV64140

PASS SW F/BOARDS GL1500C
!
BLV64640