VTX 1800
!

Air Horns - Honda VTX1800
!
Larger picture
AHVTX
Air Horns for Honda VTX1800. These horns give a loud warning blast of 128 decibels. Uses the stock horn button. Can be easily installed in 30-40 minutes. The trumpets are triple plated chrome as well as the mounts and brackets so the shine and finish will last for years to come. They are completely waterproof. No cutting or drilling is required. Trumpet covers are included.

The air compressor creates instant air pressure to the horns. Since the pressure is created so fast there is no need for a storage tank as on Semi Trucks and RVs. Although the pressure is very low (12-15 psi) it delivers a large volume of air (3 CFM or cubic feet per minute). This low-pressure high volume air supply causes the diaphragm inside the horn to vibrate at a high rate of speed or *frequency* the exact speed at which it vibrates is varied by the length of the horn or trumpet. Together the horn set produces an extremely loud 128-decibel warning blast. This is approximately 4 times louder than most electric motorcycle horns, which usually rate at 87 decibels.

Electric Horn Hardware Kit - Honda VTX
!
Larger picture
EH220
Hardware kit used to install our electric horns onto Honda VTX’s. Mounts behind engine below the swing arm—hidden. Kits include a relay, fuse, all wiring, and mounting hardware along with detailed instructions.

Rider Peg Adaptor Set for Honda

!
Larger picture
PEGSHA
Peg adaptors allow you to replace your stock rider pegs with any Rivco peg set for added comfort and good looks. Fits Honda GL1800, Rune, all VTX C models

VTX1300 & 1800 Retro Billet Brake Pedal Cover
!
Larger picture
VTXR025
This slip on brake pedal cover is the finishing touch to match our Billet Driver Boards or can be used alone. Slips on and is held in place with a set screw. Machined from billet aluminum and triple chrome plated.

VTX1300 & 1800 Retro Billet Driver Boards
!
Larger picture
VTXR024
The stock boards on your bike do the job, they keep your feet from dragging on the ground, but have you ever noticed that they look more like the gas pedal on a dump truck rather than something that belongs on your bike. RIVCO’s Driver Boards, on the other hand, are 20% larger in surface area than the stock boards and will give you more room to move your feet around and reduce fatigue on long trips. The soft neoprene rubber inlays greatly reduce vibration. Their shape and angle will give your bike that highly-customized look. They are CNC machined from solid billets of aircraft aluminum: triple chrome-plated and come with all required hardware. They also have a replaceable drag-warning indicator on the bottom leading edge to prevent scraping the boards during hard cornering.

Honda VTX1800 Driver Boards (C & F Models)
!
Larger picture
VTX024
20% larger in surface area than the stock boards that will give you more room to move your feet around and reduce fatigue on long trips. The soft neoprene rubber inlays greatly reduce vibration. Their shape and angled rubber inlays will give your bike that "highly customized" look. They are CNC machined from solid billts of aircraft aluminum; triple chrome-plated and come with all required hardware. The also have a replaceable drag-warning indicator on the bottom leading edge to prevent scraping the boards during hard cornering.

VTX Passenger Boards Relocation Arms

!
Larger picture
VTX005-5
Used to move the passenger boards forward 3 1/2" and further increase passenger leg room and comfort. When saddlebags are installed on this model there is little or no room between the passenger peg and the saddlebag for the passengers heel. By moving the boards forward 3 1/2" you will gain the needed heel room as well as allow the passenger to be in a more relaxed seating position.

VTX1800 Billet Front Caliper Covers (pair)
!
Larger picture
VTX030
These Billet Front Caliper Covers (sold in pairs) hide most of the unsightly black and add an eye catching accent to the brake calipers. They are CNC machined from billet aluminum and triple chrome plated. They attach easily and securely using 3M VHB double faced tape.

VTX1800 Billet Rear Caliper Cover (single)
!
Larger picture
VTX031
This Billet Rear Caliper Cover hides most of the unsightly black and add an eye catching accent to the rear brake caliper. It is machine from billet aluminum and triple chrome plated. Attaches easily and securely with 3M VHB double faced tape. Sold individually.

VTX1800 C Model Solo Rack
!
Larger picture
VTXC010
Go from cool solo look to passenger comfort with RIVCO's quick detach design. The rack is laser cut from steel, formed to hug the contour of the rear fender, polished and triple chrome-plated. Allows you to go back and forth between solo rack and passenger seat in seconds without tools. Comes with all required stainless steel hardware and detailed mounting instructions.

VTX1800 Chrome Radiator Cover
!
Larger picture
VTX020
Chrome Radiator Cover. Laser Cut and triple chrome plated. This product enhances the stock VTX radiator and will not effect engine cooling. Bolts on in seconds.

VTX1800 Chrome Rotor Covers
!
Larger picture
VTX002
These formed steel covers have a triple plated chrome finish and completely cover the visible portions of the rotors while still allowing heat to dissipate from the open/back side. Installation takes approximately 20 minutes and requires removal of the axle bolt. Sold in pairs.

VTX1800 Drive Shaft Cover
!
Larger picture
VTX016
This form steel cover is triple chrome plated and fits over the drive shaft housing (left side of swingarm) installs in minutes with clamps provided.

VTX1800 Frame Covers
!
Larger picture
VTX014
6 inch wide X 8 inch tall. 1 set of 2 pieces consisting of left and right. Covers the entire cast (rough) portion of the frame below the side covers. The covers are laser cut and formed from .040 steel and triple plated chrome. They are attached by one polished stainless button head allen screw with an expanding rubber plug which is inserted into the swingarm pivot hole after the stock round chrome cap is removed. Further security is added by the use of double faced 3M body moulding adhesive strips.

VTX1800 Front Caliper Covers
!
Larger picture
VTX003
Bolts on in minutes, covers most visible parts of calipers. Made of formed steel finished in a triple chrome plating process. Actually helps dissipate brake heat faster.

VTX1800 Handle Bar Risers Aluminum
!
Larger picture
VTX017A
These CNC Machined Billet Aluminum Risers bring the handle bars back towards the rider 1 1/2 inches and up 3/4 of an inch. This significantly reduces the riders back strain or reaching forward for the handlebars. Allows a more upright position rather than a leaning forward making long rides a pleasure. They have a polished aluminum finish and bolt directly on in minutes. Retains the stock cables, hoses and wiring.

VTX1800 Handle Bar Risers Chrome
!
Larger picture
VTX017
These CNC Machined Billet Aluminum Risers bring the handlebars back towards the rider 1 1/2 inches and up 3/4 of an inch. This significantly reduces the riders back strain or the reaching forward for the handle bars. Allows a *cruiser* position rather than leaning forward making long rides a pleasure. They have a triple plated chrome finish and bolt directely on in minutes. Retains all stock cables, hoses and wiring.

VTX1800 Highway Mounts w/o Pegs
!
Larger picture
VTX004
These mounts are Laser Cut CNC Machined Steel with a triple plated chrome finish. Includes all necessary stainless steel hardware for mounting. We have machined a *U* shaped mounting bracket that wraps around the frame down tube and attaches to a solid steel mounting block with a special pad to grip the frame securely to prevent slipping and without damaged to the frame. The arm itself 6 inches long but do not let this fool you, it can rotate 360 degrees, there is a series of holes in the arm and in the mounting block with a locking pin that allows over 72 DIFFERENT MOUNTING ANGLES, not to mention that it can slide up and down on the frame down tube about an inch or so. Anti-Vibration pegs sold seperatley.

VTX1800 Passenger Boards
!
Larger picture
VTX005
GREAT TOURING COMFORT! Keep your passengers comfortable and happy with RIVCO's high quality triple chrome plated passenger boards. The boards themselves greatly increase passenger foot and leg support over the stock pegs. Floorboards are inlayed with anti-vibration neoprene pads.

VTX1800 & 1300 R Model Solo Rack

!
Larger picture
VTX010
Go from cool solo look to passenger comfort with RIVCO's quick detach design. Allows you to go back & forth between solo rack and passenger seat in seconds without tools. Laser cut form high quality steel and triple chrome plated. Comes with all required stainless steel hardware and detailed mounting instructions.